Floor Coating Systems - Methyl Methacrylates / mMa

Our 400 series methyl methacrylate resurfacing systems are based on 100% solids, reactively cured methacrylate binder resins, pigments and inert silica or quartz fillers.

They are quick drying, cure at temperatures as low as -20°F, resists cracking, USDA approved and highly resistant to acids and alkalis.

Methyl Methacrylates floorings are best suited for chemical processing areas, food processing facilities, freezers and refrigerated warehouses.

Our Methyl Methacryate products are available as a Primer, Body Coat and Top Coat.

Additional mMa product references:

mMa Equipment Checklist
mMa Safety Environment
mMa Bond Test
mMa Catalyst Dosing Table

VIDEO - mMa Product Video

Dairy Facility Before & After:

Liquid Manufacturing Facility Before & After:



Primer
Duraguard™ 400 mMa

Duraguard 400 is a two-component, fast-setting Methyl Methacrylate (mMa) primer typically applied direct to prepared concrete at 100 SF/GA. It is comprised of a methyl methacrylate resin, an isocyanate bond enhancer and a catalyst. Technical Data Sheet MSDS - Duraguard 400 mMa Resin MSDS - Duraguard mMa Catalyst MSDS - Duraguard mMa I Component CSI Specification

Body Coat
Duraflow™ 450 mMa		Duraflow 455 mMa

Duraflow 450 mMa is a semi self leveling, three component body coat that is typically applied at a thickness from 1/16” – 1/8” over a properly primed substrate. This body coat is then normally top coated with either Duraguard 420 mMa or Duraguard 425 mMa. Duraflow 450 mMa gives the topping system superior impact and abrasion resistance in areas subject to heavy traffic. Typical application areas are food processing facilities, commercial kitchens and bottling plants. Technical Data Sheet MSDS Duraflow 450 mMa Resin MSDS Duraguard mMa Catalyst MSDS Duraflow mMa Pigment MSDS Duraflow mMa Filler CSI Specification		Duraflow 455 mMa is a semi self leveling, three component body coat that is typically applied at a thickness from 1/16” – 1/8” over a properly primed substrate. Duraflow 455 mMa is specifically designed for use on floors that will be in service at below freezing temperatures. The flexible resins in Duraflow 455 mMa enable this product to withstand high impact and abrasion in situations where other coatings will crack and delaminate because of the cold. Technical Data Sheet MSDS - Duraguard 455 mMa Resin MSDS Duraflow mMa Pigment MSDS Duraflow mMa Filler

Top Coat
Duraguard™ 420 mMa		Duraguard 425 mMa

Duraguard 420 is a two-component, high build, Methyl Methacrylate (mMa) coating. It is comprised of a mMa resin and a catalyst. An accelerator is available for use in cold temperatures. Technical Data Sheet MSDS Duraguard 420 mMa Resin MSDS Duraguard mMa Catalyst CSI Specification Technical Bulletin		Duraguard 425 is a two-component, high build, Methyl Methacrylate (mMa) pigmented topcoat typically applied at 100 SF/GA. It is comprised of a mMa resin and a catalyst. Technical Data Sheet MSDS Duraguard 425 mMa Resin MSDS Duraguard mMa Catalyst MSDS Duraguard mMa Pigment CSI Specification

300 Edwards Street • Madison, Ohio 44057 • Toll Free: 800.486.7866 • Phone: 440.428.2105 • Fax: 440.428.7091 • Email: info@chemfloors.com